ThruLink™

You will find the latest firmware for the KBC ThruLink here. These are updates only.

6.2.1.10 - 20240125

Implement secure discovery protocol that allows for IP identification and resetting of the unit. Useful to identify a forgotten IP address.
Include advanced routing configuration in wancheck. During a service restart any existing advanced routing routines would be removed.
Disconnect RX/TX RF circuits before rebooting when in LTE mode. Previously powering down the module could cause a panic on the communication interface.
Fix a bug where the subnet was not been set correctly on the WAN interface.
Show chipset sub version when in LTE mode.
Improve removal of stale nodes/edges from active connection list.
Prefered MTU size occurs more often which improves packet size discovery.
WAN check now deals with interfaces that don't become active after a period of time. Before the service would wait until activity occured before progressing. It now assumes something has gone wrong and forces a reboot.
During a reboot, first disconnect from any active session. This should reset any PDU to CPE network session.
Improve storing and loading of platform identity to be used for validation when upgrading.
Display Connection Type within signal strength indicator.

6.2.1.10 - 20240125

Implement secure discovery protocol that allows for IP identification and resetting of the unit. Useful to identify a forgotten IP address.
Include advanced routing configuration in wancheck. During a service restart any existing advanced routing routines would be removed.
Disconnect RX/TX RF circuits before rebooting when in LTE mode. Previously powering down the module could cause a panic on the communication interface.
Fix a bug where the subnet was not been set correctly on the WAN interface.
Show chipset sub version when in LTE mode.
Improve removal of stale nodes/edges from active connection list.
Prefered MTU size occurs more often which improves packet size discovery.
WAN check now deals with interfaces that don't become active after a period of time. Before the service would wait until activity occured before progressing. It now assumes something has gone wrong and forces a reboot.
During a reboot, first disconnect from any active session. This should reset any PDU to CPE network session.
Improve storing and loading of platform identity to be used for validation when upgrading.
Display Connection Type within signal strength indicator.

6.2.1.10 - 20240125

Implement secure discovery protocol that allows for IP identification and resetting of the unit. Useful to identify a forgotten IP address.
Include advanced routing configuration in wancheck. During a service restart any existing advanced routing routines would be removed.
Disconnect RX/TX RF circuits before rebooting when in LTE mode. Previously powering down the module could cause a panic on the communication interface.
Fix a bug where the subnet was not been set correctly on the WAN interface.
Show chipset sub version when in LTE mode.
Improve removal of stale nodes/edges from active connection list.
Prefered MTU size occurs more often which improves packet size discovery.
WAN check now deals with interfaces that don't become active after a period of time. Before the service would wait until activity occured before progressing. It now assumes something has gone wrong and forces a reboot.
During a reboot, first disconnect from any active session. This should reset any PDU to CPE network session.
Improve storing and loading of platform identity to be used for validation when upgrading.
Display Connection Type within signal strength indicator.

6.2.1.10 - 20240125

Implement secure discovery protocol that allows for IP identification and resetting of the unit. Useful to identify a forgotten IP address.
Include advanced routing configuration in wancheck. During a service restart any existing advanced routing routines would be removed.
Disconnect RX/TX RF circuits before rebooting when in LTE mode. Previously powering down the module could cause a panic on the communication interface.
Fix a bug where the subnet was not been set correctly on the WAN interface.
Show chipset sub version when in LTE mode.
Improve removal of stale nodes/edges from active connection list.
Prefered MTU size occurs more often which improves packet size discovery.
WAN check now deals with interfaces that don't become active after a period of time. Before the service would wait until activity occured before progressing. It now assumes something has gone wrong and forces a reboot.
During a reboot, first disconnect from any active session. This should reset any PDU to CPE network session.
Improve storing and loading of platform identity to be used for validation when upgrading.
Display Connection Type within signal strength indicator.